 |
| DTS DYNAMARK Computerized Dynamometer Capable of testing over 2,000 HP at 15,000 RPM SUPERFLOW SF-600 Computerized Flow Testing The latest in flow testing technology HINES Computerized Engine Balancing The high performance industry standard SUNNEN CV616 Deck Plate Power Honing The choice of all high performance engine builders SUNNEN Head Rebuilding Equipment For precise valve grinding, seat and guide installation SUNNEN Line Honing For true bearing alignment and clearance SUNNEN Rod reconditioning For proper bearing crush and clearance |
CRANKSHAFT SERVICES
Clean 19.00
Chamfer oil holes 25.00
Magna flux 25.00
Clean & polish _ 50.00
Grind - most 121.00
Cross-drill mains _ 125.00
Clean 19.00
Chamfer oil holes 25.00
Magna flux 25.00
Clean & polish _ 50.00
Grind - most 121.00
Cross-drill mains _ 125.00
COMPETITION
HEAD WORK
Disassemble race heads ——— 40.00
Clean aluminum heads ———— 60.00
Street/Perf valve job ————-- 150.00
Competition Multi-angle
valve job —————————-- 230.00
Assemble & Set installed height 65.00
Back-cut valves ea.——————- 3.00
Cut for teflon seals —————— 40.00
Cut for over-size springs
diameter only ————————- 65.00
Machine for screw-in studs —— 150.00
canted heads ———- 195.00
Install bronze guides & wet hone
to size ——————————— 180.00
Machine for oversize valves —--180.00
Drill steam holes SBC — iron — 55.00
Drill steam holes — aluminum —94.00
Pin rocker studs w/pins ——— 75.00
HEAD WORK
Disassemble race heads ——— 40.00
Clean aluminum heads ———— 60.00
Street/Perf valve job ————-- 150.00
Competition Multi-angle
valve job —————————-- 230.00
Assemble & Set installed height 65.00
Back-cut valves ea.——————- 3.00
Cut for teflon seals —————— 40.00
Cut for over-size springs
diameter only ————————- 65.00
Machine for screw-in studs —— 150.00
canted heads ———- 195.00
Install bronze guides & wet hone
to size ——————————— 180.00
Machine for oversize valves —--180.00
Drill steam holes SBC — iron — 55.00
Drill steam holes — aluminum —94.00
Pin rocker studs w/pins ——— 75.00
BALANCING SERVICES
Standard Passenger V-6 or V-8 255.00
4 cylinder 200.00
Crankshaft ONLY V-6 or V8 166.00
Straight 4 or 6 cylinder 137.00
Pistons HR
Rods HR
Flywheel or flexplate Plate 68.00
Pressure plate (after flywheel is balanced) P.O.R.
Heavy Metal Installation Labor
Each 63.00 Welding
and Excess Metal Removal
per hour 75.00
NEEDED FOR BALANCING
Crank, rods, pistons & pins, locks, rings,
bearings,flywheel and bolts,pressure plate
and bolts,Vibration damper and bolt.
All parts must be clean and unassembled
(pistons off rods and rings off pistons etc.)
Standard Passenger V-6 or V-8 255.00
4 cylinder 200.00
Crankshaft ONLY V-6 or V8 166.00
Straight 4 or 6 cylinder 137.00
Pistons HR
Rods HR
Flywheel or flexplate Plate 68.00
Pressure plate (after flywheel is balanced) P.O.R.
Heavy Metal Installation Labor
Each 63.00 Welding
and Excess Metal Removal
per hour 75.00
NEEDED FOR BALANCING
Crank, rods, pistons & pins, locks, rings,
bearings,flywheel and bolts,pressure plate
and bolts,Vibration damper and bolt.
All parts must be clean and unassembled
(pistons off rods and rings off pistons etc.)
COMPETITION ENGINE SERVICES
File-fit rings 70.00
Blueprinting P.O.R.
Side clearance rods P.O.R.
Degree cam per hour 60.00
C.C. heads per hour 60.00
Custom engine assembly P.O.R.
Check bearing clearances min 125.00
File-fit rings 70.00
Blueprinting P.O.R.
Side clearance rods P.O.R.
Degree cam per hour 60.00
C.C. heads per hour 60.00
Custom engine assembly P.O.R.
Check bearing clearances min 125.00
FLOW TESTING & PORTING
First hour 75.00
Each additional hour 75.00
First hour 75.00
Each additional hour 75.00
| Minimum charge (up to 4 hours) 400.00 Hourly rate thereafter 75.00 Full day rate 650.00 Time includes Automotive Machine personnel setting up the engine and removal of the engine from dyno, it does not include Automotive Machine personnel working on engine during the session unless it is an engine that we have assembled. Automotive Machine is not responsible for damage incurred to engines while ran on dyno |
Miscellaneous Cleaning Services
Clean iron intake and magnaflux 48.00
Clean & glass bead
aluminum intake 60.00
Clean iron intake and magnaflux 48.00
Clean & glass bead
aluminum intake 60.00
| Shop Labor not covered in this price list is based on a minimum charge of $60.00 per hour |
| Credit Cards Subject to 3% Charge |
| NO WARRANTY ON COMPETITION WORK EXCEPT WORKMANSHIP Because of core shifts in heads we cannot guarantee that machining will not go into water jackets |
MACHINE SHOP PRICE SCHEDULE May 2008
Machine shop price list, HP machine shop, race car machine shop, machine shop labor charges, machine shop prices,
BLOCK MACHINING
Pre-clean ——————————- 28.00
cam bearings & galley plugs)
Oven bake and steelabrate —--- 65.00
Clean misc. parts ———————- H.R.
Pressure check V-8 block ——-- 85.00
Tap oil holes & install restrictors
SBC or BBC ————————— 35.00
Tap front galley holes ———— 28.00
Clearance block for rods ———— H.R.
Install deck plugs ——————— H.R.
Resize block (up to .060) 4 cyl -130.00
6 cyl —155.00
8 cyl —175.00
Resize V-8 w/torque plates
Street ———— 230.00
Race finish —— 285.00
Competition re-hone w/plates — 180.00
Deck square to mains ————- 120.00
ea. add. .005 per cyl. —————-- 1.50
Install sleeve (labor) ————— 135.00
Ball hone V-8 ————————- 50.00
Install cam bearings —————-- 60.00
(hand fit extra)
Install galley plugs ——————- 27.00
Install freeze plugs, each ———— 3.00
Line hone (touch -in) ————-- 150.00
( with studs ) ——— 165.00
Line hone 400 SBC —————- 190.00
Line hone damaged blocks ——— H.R.
Fill block w/HARDBLOK ———- 150.00
Sonic check block —————— 120.00
Install Buick block girdle ———- 550.00
Machine & install Poston Pan — 150.00
Pre-clean ——————————- 28.00
cam bearings & galley plugs)
Oven bake and steelabrate —--- 65.00
Clean misc. parts ———————- H.R.
Pressure check V-8 block ——-- 85.00
Tap oil holes & install restrictors
SBC or BBC ————————— 35.00
Tap front galley holes ———— 28.00
Clearance block for rods ———— H.R.
Install deck plugs ——————— H.R.
Resize block (up to .060) 4 cyl -130.00
6 cyl —155.00
8 cyl —175.00
Resize V-8 w/torque plates
Street ———— 230.00
Race finish —— 285.00
Competition re-hone w/plates — 180.00
Deck square to mains ————- 120.00
ea. add. .005 per cyl. —————-- 1.50
Install sleeve (labor) ————— 135.00
Ball hone V-8 ————————- 50.00
Install cam bearings —————-- 60.00
(hand fit extra)
Install galley plugs ——————- 27.00
Install freeze plugs, each ———— 3.00
Line hone (touch -in) ————-- 150.00
( with studs ) ——— 165.00
Line hone 400 SBC —————- 190.00
Line hone damaged blocks ——— H.R.
Fill block w/HARDBLOK ———- 150.00
Sonic check block —————— 120.00
Install Buick block girdle ———- 550.00
Machine & install Poston Pan — 150.00
ROD & PISTON WORK
Clean rods - each ———————- 3.00
Remove & replace press fit
Each ———————————–—— 8.50
Remove & replace non stock
applications ————————–——-H.R.
Check big end - each ——————- 3.50
Check big end & hone to size
Each ————————————–-- 5.25
Re-condition rods
stock - each ————————–-— 22.00
using HP bolts - each —————–- 26.00
Magnaflux rods - each —————— 3.00
Pin-fit small end - each —————- 9.00
Re-bush small end - ea ————— H.R.
Drill & chamfer oil holes
Each —————————————- 4.50
Pin fit piston - each ——————— 9.00
Fly-cut reliefs, dome machining &
contouring ——————————— H.R.
Clean rods - each ———————- 3.00
Remove & replace press fit
Each ———————————–—— 8.50
Remove & replace non stock
applications ————————–——-H.R.
Check big end - each ——————- 3.50
Check big end & hone to size
Each ————————————–-- 5.25
Re-condition rods
stock - each ————————–-— 22.00
using HP bolts - each —————–- 26.00
Magnaflux rods - each —————— 3.00
Pin-fit small end - each —————- 9.00
Re-bush small end - ea ————— H.R.
Drill & chamfer oil holes
Each —————————————- 4.50
Pin fit piston - each ——————— 9.00
Fly-cut reliefs, dome machining &
contouring ——————————— H.R.
HEAD WORK
4-CYLINDER
Oven bake & steelabrate ——— 28.00
Magnaflux —————————- 16.00
Valve job —————————— 70.00
Overhead cam — 90.00
Overhead cam 4V ——120.00
Diesel 2V —————-————- 90.00
For non-adj. valves add ———--12.00
Straight 6-CYLINDER
Oven bake & steelabrate ——— 40.00
Magnaflux —————————- 20.00
Valve job —————————— 95.00
Diesel —————————-—- 140.00
For non-adj. valves add ———-- 17.00
V-6 & V8 cylinder
Oven bake & steelabrate ——— 46.00
Magnaflux —————————- 30.00
Valve job ————————— 115.00
Diesel —————————--— 155.00
Perf. valve job ——————— 150.00
(any non-stock cam)
For non-adj. valves add ———- 22.00
DISASSEMBLY AND ASSEMBLY @ HR
4-CYLINDER
Oven bake & steelabrate ——— 28.00
Magnaflux —————————- 16.00
Valve job —————————— 70.00
Overhead cam — 90.00
Overhead cam 4V ——120.00
Diesel 2V —————-————- 90.00
For non-adj. valves add ———--12.00
Straight 6-CYLINDER
Oven bake & steelabrate ——— 40.00
Magnaflux —————————- 20.00
Valve job —————————— 95.00
Diesel —————————-—- 140.00
For non-adj. valves add ———-- 17.00
V-6 & V8 cylinder
Oven bake & steelabrate ——— 46.00
Magnaflux —————————- 30.00
Valve job ————————— 115.00
Diesel —————————--— 155.00
Perf. valve job ——————— 150.00
(any non-stock cam)
For non-adj. valves add ———- 22.00
DISASSEMBLY AND ASSEMBLY @ HR
REPLACE GUIDES
One ———--each —————- 20.00
2-4 ———— each ——————15.00
5 or more —-each ——————- 9.50
REPLACE SEATS
1 includes set up 25.00
5 or more - each —————— 12.50
Aluminum heads
1 includes set up 30.00
2 - 4 ——— each ——–—-—–—20.00
5 or more - each —————— 15.00
One ———--each —————- 20.00
2-4 ———— each ——————15.00
5 or more —-each ——————- 9.50
REPLACE SEATS
1 includes set up 25.00
5 or more - each —————— 12.50
Aluminum heads
1 includes set up 30.00
2 - 4 ——— each ——–—-—–—20.00
5 or more - each —————— 15.00
HEAD RE-SURFACING
Cast Iron Aluminum
4-cyl 40.00 46.00
Straight 6-cyl 52.00 67.00
V-6 or V8 Pair
(up to .010) 65.00 80.00
Each additional
(.0050 per cyl) 1.50 1.50
V-6 or V8 Intake
or exhaust side Priced per job
Additional Charge For Extra Set-up
Cast Iron Aluminum
4-cyl 40.00 46.00
Straight 6-cyl 52.00 67.00
V-6 or V8 Pair
(up to .010) 65.00 80.00
Each additional
(.0050 per cyl) 1.50 1.50
V-6 or V8 Intake
or exhaust side Priced per job
Additional Charge For Extra Set-up